民用航空產品和零部件獲得外國設計批準接受或認可的指南

時間：2014-11-22 11:13來源：藍天飛行翻譯公司整理 作者：民航翻譯 點擊：次

The Importing State CAA usually accepts or validates the design approval of CAAC for the civil aeronautical products or articles by issuing "Type Acceptance" or "Validation of type certificates".當采取頒發“型號接受證”方式時，進口國 CAA 通常對民航局關于民用航空產品或零部件的設計批準予以完全承認和接受。
When issuing "Type Acceptance", the Importing State CAA usually fully acknowledge and accept the CAAC design approval of civil aeronautical products or articles.當采取頒發“型號認可證/型號合格證”方式時，進口國 CAA 在承認并接受民航局關于民用航空產品或零部件的設計批準的同時，通常會對民用航空產品或零部件提出需要符合的附加技術條件，并最大程度委托、承認和接受民航局對民用航空產品或零部件符合這些附加技術條件做出的結論。
When issuing "Validation of type certificates", the Importing State CAA acknowledge and accept CAAC design approval of the civil aeronautical products or articles and at the same time, usually propose additional technical requirements that should be met regarding the civil aeronautical products or articles, and recognize and accept, to the maximum extent, the conclusions by CAAC regarding whether civil aeronautical products or articles meet these additional technical requirements.此時，應進口國CAA 要求，可能需要申請人按 2.8 段要求向進口國 CAA 提交以下信息或數據：
At this time, as requested by the Importing State CAA, the applicant might need to submit the following information or data to the Importing State CAA according to requirements in paragraph 2.8:
(1) 用于支持進口國 CAA 做出符合性結論所需的試驗計劃和報告；
(1) Test plans and test reports necessary to support the Importing State CAA to make findings of compliance.
(2) 用于支持進口國 CAA 做出符合性結論所需的計算及分析；
(2) Calculation and analysis necessary to support the Importing State CAA to make findings of compliance.
(3) 上述兩項相應的民用航空產品或零部件的設計數據。
(3) Relevant design data of the civil aeronautical products or articles regarding the above two.
注：進口國 CAA 做出接受或認可結論時，通常需要民用航空產品或零部件已取得民航局的設計批準。
Note: when the Importing State CAA make acceptance or validation conclusion, it is usually required that the design approval of the civil aeronautical products or articles have been obtained from CAAC.

航空翻譯 m.ajkitchenandbath.com
本文鏈接地址：民用航空產品和零部件獲得外國設計批準接受或認可的指南